 |
|
 |
Installation Components |
| Flagpole Components, Inc. provides a complete line of
Foundation Sleeves and Anchor Bolts for flagpole
installation. Flagpole Components, Inc. does not attempt
to provide recommendations for the concrete base
dimensions. Since soil conditions vary, it is suggested
that an engineer be consulted as to the recommended size.
Extreme caution should be exercised when installing a
flagpole near overhead power lines or in the vicinity of
buried cables or pipes. Contact your local utility companies prior to installation. |
Please click on a selection below |
|
Anchor Bolts |
Foundation Sleeves |
 |
Anchor Bolts |
| For use in shoebase installation. Anchor bolts are constructed from A35M55 high strength carbon steel ASTM A675 GRADE 90 with a minimum yield of 55,000 PSI. They are hot dip galvanized over the full length to meet the requirement of ASTM 153. Including two nuts, two flat washers and a lock washer, also galvanized. | |
| SIZE | BASE PLATE SIZE | GROUND ROD SIZE | PART NO. | 1-2 | 3-6 | 7+ |
| A | 12" x 12" | 3/4" x 18" | GCA-1410 | 31.00 | 29.00 | 27.50 |
| B | 14" x 14" | 3/4" x 18" | GCA-1420 | 34.00 | 32.00 | 30.50 |
| C | 16" x 16" | 3/4" x 24" | GCA-1430 | 38.00 | 35.50 | 33.50 |
| D | 18" x 18" | 3/4" x 24" | GCA-1440 | 42.00 | 39.00 | 37.00 |
 |
Foundation Sleeve AssemblyThe most common flagpole installation method, the foundation sleeve assembly is fabricated from 16GA. galvanized steel welded to a base plate with a square dimension at least 4" greater than the outside diameter of the sleeve. A 3/4" diameter grounding spike is welded to the base plate. Centering wedges are welded inside the assembly to aid in flagpole alignment. A setting plate is welded to the grounding spike to provide the installer with a method of resting the assembly on the bottom of the excavated hole and allowing the concrete to completely encase the unit. Generally accepted industry practice calls for 1' of the flagpole to be encased in the ground sleeve assembly for each 10' of exposed flagpole height and, for ease in vertical alignment of the shaft, the inside diameter of the sleeve should be at least 2" greater than the flagpole diameter with the area between the flagpole and the sleeve filled with dry sand. If your requirements are not listed below, consult the factory regarding custom sizes or applications. Each ground sleeve assembly listed below shows a size for the base plate assembly. This is the lower section of the ground sleeve assembly and is fabricated from 3/16" steel plate with four welded centering wedges, a 3/4" spike and a 6" x 6" setting plate. By omitting the corrugated sleeve, shipment of this unit can be via UPS as a greatly reduced rate. The customer then attaches his own sleeve material such as steel pipe or PVC pipe with angle brackets and bolts. |
| SLEEVE LENGTH |
INSIDE DIAMETER |
BASE PLATE ASSEMBLY |
PART NO. | 1-2 | 3+ |
| 3'0" | 8" | SIZE A | GCA-3008 | 82.00 | 78.00 |
| 3'0" | 10" | SIZE B | GCA-3010 | 100.00 | 94.00 |
| 3'6" | 8" | SIZE A | GCA-3508 | 98.00 | 92.00 |
| 3'6" | 10" | SIZE B | GCA-3510 | 110.00 | 104.00 |
| 4'0" | 10" | SIZE B | GCA-4010 | 114.00 | 108.00 |
| 4'0" | 12" | SIZE C | GCA-4012 | 130.00 | 122.00 |
| 4'6" | 12" | SIZE C | GCA-4512 | 148.00 | 140.00 |
| 5'0" | 12" | SIZE C | GCA-5012 | 156.00 | 148.00 |
| 5'0" | 14" | SIZE D | GCA-5014 | 184.00 | 172.00 |
| 6'0" | 14" | SIZE D | GCA-6014 | 206.00 | 194.00 |
| 7'0" | 14" | SIZE D | GCA-7014 | 225.00 | 212.00 |
| 8'0" | 14" | SIZE D | GCA-8014 | 250.00 | 236.00 |
|
 |
Welcome | How to order | Catalog | What's new? | Contact us
Copyright © 1997 Concord Industries